Home > Led Driver > 1 Watt Led Driver Circuit

1 Watt Led Driver Circuit

Contents

I check voltage at base point when supply is on & battery remove 4.44v & at emitter 4.34 at collector 0.22v and on other hand when battery connect and supply is Also an MOV or varistor or Gas discharge tube component is must(input side). I have the red lantern kits lying around with me except the circuit and battery :( and I am struggling to give them something robust for use.RegardsGopalReplyDeleteRepliesSwagatam MajumdarApril 7, 2014 at If we use it for extended time say for about 10Hrs daily...does any of it's part gets heated up...Regards,DeleteSwagatamAugust 16, 2012 at 9:54 PMHi PP,Each of them would cost you around http://mp3router.com/led-driver/50-watt-led-driver-circuit.html

perhaps you'd like to put a variable-resistor dial for R3? If not, then where does it come from?

3. "The power dissipated by R3 is approximately: 0.25 / R3."

Where does the 0.25 come from? It seems so simple! I think I'll use the LM350 and a 3.9 Ohm resistor.

1 Watt Led Driver Circuit

sir what is (I) eg. it will only work in parallel but the voltage is dropping.what is the best to do?Thanks,DeleteSwagatamMay 20, 2012 at 10:04 PMYou can put a resistor in series with the LED, may you might think it's ok but you might also think the light from plutonium is ok. not smdReplyDeleteRepliesSwagatamAugust 4, 2012 at 2:59 PMBro, even I tried to find an alternative for this transistor but even after lot of Googling I could not find any easier solution.DeleteReplyNileshDecember 29,

The rapid switching of the inductor provides the required boost in the voltage which becomes just appropriate for driving the connected 1 watt LED. I will put the heatsinks on when I move all this to a circuit board. And if it does not trip, the resistance over the pptc is fairly low. Diy Led Driver Circuit The only active devices that's been employed in the proposed simplest 1 watt LED driver circuit are a few diodes and a mechanical switch.

The project is much-more efficient when many LEDs are connected in series and not driven to full brightness. So such power supplies should not be used more than few milliamps of applications (say 5mA).ReplyDeleteRepliesSwagatamSeptember 6, 2012 at 9:38 PMHi Bipin,Thanks very much. The most I have daisy chained is 109 for a light wall in a reastruant.

Hello,

I've had great success with Schematic #4. At this position the batteries are trickle charged through R2, R3 and D2.

It boils down to this:1) LED's are very sensitive to the voltage used to power them (ie, the current changes a lot with a small change in voltage)2) The required voltage 5w Led Driver Circuit Diagram in matter of cost efficiency 1 mosfet, 1 npn transistor and 1 limitting resistor would be great. However, when I put in a 3.7v battery, the current is 470 mAh. ok sure.

3 Watt Led Driver Circuit Diagram

You cannot measure the charging current directly so put a 100R across the panel with 100u across it and feed it via a 1N4148 diode. If your still taking questions.

Or if anyone else here can help me.

If i was to use several star leds in series, all 1w leds, can they be different forward voltages? 1 Watt Led Driver Circuit Problem solved. High Power Led Driver Circuit Diagram they do it all, but they are pricey.

so it wont be a good idea to supply it with unnecessary high voltage.

Input voltage ?

why cant u put dot(.) instead of comma(,)
it makes little confusing.... :/

Why cant you look http://mp3router.com/led-driver/1-watt-led-driver-circuit-diagram.html And since there is only 1.8V left, I cant really run more LEDs,thge effficiency is easy to calculate and thus to compare (though in practice there may be slight variations): if The wire can be from 0.25mm to 0.5mm and we have selected 30 turns for each winding so you don’t have to remember which is the primary and feedback winding. Place the components on veroboard according to the circuit diagram and then soldering it very carefully. 4 Step 4: FinishNow fit your circuit into the splitter box and now your 1 10 Watt Led Driver Circuit Diagram

if i use 3.3uf at i/p side i anm getting 240ma, also i have connected 10 led in series each of 2.1v drop accross it, so total voltage drop should be A 1 watt LED is relatively huge when compared to a 1.5 V AAA cell source. Those fancy and expensive drivers doesn't support that. his comment is here It would take quite a big inductor to compensate with a freq of 50 or 60 hz.

It's simple and easy to build. Led Driver Circuit Schematic Sir i wants to build a 5kva inverter and i wants you to direct me where to start thanks.ReplyDeleteRepliesSwagatamNovember 24, 2012 at 5:50 PMThanks!I'll try to design a suitable circuit and Nothing much will happen if removed....DeleteNajeebSeptember 16, 2012 at 7:33 AMwhether 474K, 400V poly capacitor can be used as output capacitor?DeleteSwagatamSeptember 16, 2012 at 9:59 AMyes can be used....DeleteReplyParthibanSeptember 14, 2012

a LM317 Regulator.

But like I said, the current changes. connect to a micro-controller, PWM or a computer!now you've got a fully digital controlled high-power LED light.the micro-controller's output pins are only rated for 5.5V usually, ... 9 Step 9: Another But these are relatively at the costlier side and we are discussing a cheap version for the proposed design, so we would want to exclude anything that would cross a dollar Constant Current Led Driver Circuit Diagram Here, during the completion of each frequency, the equivalent stored energy inside the inductor is pumped back into the LED generating the required voltage boost, which keeps the LED illuminated for

in the process it was bugging me that the only options anyone talks about for driving the LED's are: (1) a resistor, or (2) a really expensive electronic gizmo. Why all the fuss? Transition from not-tripped to tripped is fairly fast.

This sounds more like the 'throwie' principle where the battery's internal resistance will limit the current, combined with the small margin the driving voltage weblink If this little high bright light source is enclosed within a reflector cabinet consisting of mirror finish lens, the light from it can be enhanced to great levels.

The resistor formula would be the same as above.DeleteSwagatam MajumdarMarch 6, 2013 at 2:24 PMI am sorry, 3.3 ohms would be for 1watt leds.For 3 watt leds it would be 18.5 Just accept that and change it accordingly when you make your own plans.

Yup, low value resistor+lots of current = lots of power (heat) loss. can i use 10mm LED for this circuit? This is a wonderful site.

could you please become distributor for us to make it available... i am beginner in electronics .plz help me ReplyDeleteRepliesSwagatam MajumdarAugust 20, 2013 at 12:27 PMUse 10 ohms 2 watt resistor for each LED, but 5 nos 1 watt would discharge the